Skip to content

Filter & Envelope

The heart of LH-2044 is a four-pole low-pass filter whose cut-off jumps open every time your audio hits and then falls back. This chapter explains how each part responds, so you can predict what a knob will do before you touch it.

The signal path

Audio runs through LH-2044 in this order. The first three stages are the subject of this chapter; the rest are in The Output Stage.

  1. Mono sum (only when MONO is lit): left and right become one signal.
  2. Envelope detector: listens to the input and fires the envelope on each hit.
  3. Filter: four-pole low-pass at the cut-off, moved by the envelope, followed by a fixed bass lift and level makeup.
  4. Output level: the small knob in the top row.
  5. Saturation: the output op-amp's soft knee.
  6. 12-bit reduction (when 12 BIT is lit).
  7. Noise floor: a faint analog hiss.

On a stereo track without MONO, each side has its own detector, envelope and filter. A hit that only happens on the left opens only the left filter.

The filter

The SSM2044 is a four-pole filter: above the cut-off frequency it removes high frequencies at 24 dB per octave. That steep slope is why it sounds dark and thick rather than merely dull: the low end is left intact while the top falls away fast.

Cut-Off

Cut-Off runs from 20 Hz to 20 kHz. Around the default 500.0 Hz drums keep their body and lose their sizzle; below 200 Hz only the thump of kicks and bass remains; above 5 kHz the filter mostly takes the edge off. At the top of its range the cut-off is limited to just under half the sample rate, so at 44.1 kHz it tops out near 19.8 kHz.

Moves of the knob, and of the envelope, are smoothed over 20 milliseconds, so sweeps and automation never zipper or click.

Resonance

Resonance adds a peak right at the cut-off frequency. From 1 to about 5 it mostly firms up the corner of the slope, the classic rounded SSM2044 sound. From about 10 upwards the peak becomes a tone of its own that whistles as the cut-off moves, which is where envelope sweeps start to sound like a wah. The peak rises gently across the range; even at 20, LH-2044 does not self-oscillate, so it never howls on its own when the input stops.

Bass lift and level

After the filter, LH-2044 adds a fixed, gentle boost of about 4 dB below 90 Hz, and brings the overall level up by about 4 dB to make up for what the filter removes. Together they give the full, weighty low end the hardware is known for. They are part of the filter's character and are always on while LH-2044 is ON.

The envelope

Each time the detector fires, the envelope does the same thing:

  1. It rises to full in 5 milliseconds, pushing the cut-off up.
  2. It falls back over about 300 milliseconds, quickly at first and then more slowly, letting the cut-off sink back to the knob setting.

The timing is fixed. What you control is how far it pushes, with Attack, and what makes it fire, with Threshold. Once fired, the envelope runs its full course (about 305 ms) before it can fire again, so a hit landing during that time does not restart it.

Attack

Attack sets how far the envelope opens the filter, as a share of six octaves. At 100 a hit with the cut-off at 500 Hz sweeps the filter up towards 20 kHz and back; at 50 it reaches about three octaves above the knob (4 kHz); at OFF the envelope has no effect and the filter is static.

Low Cut-Off with high Attack is the classic snappy sound: dark between hits, bright on every transient.

Threshold

The detector compares the input to the Threshold level. It fires when the input has stayed below the threshold for at least 50 milliseconds and then rises above it. In practice that means: